Installing wood burning stove commercial kitchen

Note that this is not a comprehensive list of State actions -- it is meant to provide examples. If you need information about State requirements, contact your State air agency. The Colorado Department of Public Health and Environment posts wood-burning advisories on its website. During red advisories, mandatory residential burning restrictions generally apply to everyone in the 7-county Denver-Boulder metro area below 7, feet.

Colorado has a regulation that applies to the sale and installation of wood-burning appliances and the use of certain wood-burning appliances during high pollution days. This and other air quality regulations are on their Air Quality Control Commission regulations website. The state of Idaho offers taxpayers who buy new wood stoves, pellet stoves, or natural gas or propane heating units for their residences a tax deduction to replace old, uncertified wood stoves.

Burning restrictions are contained in the Rules for the Control of Air Pollution in Idaho and are applicable statewide. The model ordinance includes language for restrictions or bans on outdoor wood-fired boilers and patio wood-burning units. The Oregon Department of Environmental Quality has authority to operate and enforce a program to curtail residential solid fuel heating during periods of air stagnation. Sale and installation of uncertified wood stoves are prohibited.

When a house is sold, all used, uncertified solid fuel burning devices, other than cookstoves, in or on the property must be removed and destroyed. Solid fuel burning devices used in Oregon must meet emission performance standards established under ORS A. The Washington Department of Ecology provides information about burn bans , which wood burning devices are legal in Washington, why wood smoke is harmful to health, and how to reduce the smoke from your wood burning device.

They have established wood stove emission performance standards. Wisconsin Department of Natural Resources has an Outdoor Wood Boiler webpage that includes basic information on the device, health effects, complaint advice, and a Model Ordinance.

The model ordinance is for municipalities to use for regulating outdoor burning, open burning and burning of refuse. The model ordinance includes language for restrictions or bans on outdoor wood-fired boilers. Certain jurisdictions have established legal requirements to reduce wood smoke. For example, some communities have restrictions on installing wood-burning appliances in new construction.

The most common and least restrictive action is to limit use at those times when air quality is threatened. The appropriate agency issues an air quality alert on the days when restrictions apply. The benefit of having a HETAS installer fit your stove is that they already know every wood burning stove regulation, saving you the headache of reading up on them yourself!

Nevertheless, there are a few stove building regulations that are good for you to know about beforehand. In this blog, we will answer the following commonly asked questions…. Do you need planning permission to install a wood burning stove? Is it a legal requirement to have a flue liner? What are the hearth regulations for a log burner? What are the ventilation requirements for a wood burning stove?

Do you need a carbon monoxide alarm for a stove? Read on to find out more about these building regulations so you can get your new wood burner or multi fuel stove fitted without any issues….

Related: Stove Installation Advice. In this case, your installer is qualified to certify the works themselves, and will issue a certificate of compliance as proof.

This will be signed by your installer and used to notify your council of the building work. If you fit your stove yourself, or have a non-HETAS installer do the job, you will need to tell your local Building Control department before you start any work.

When the work is complete, they will need to inspect it to ensure all building regulations have been met. This will be at your expense, so factor this into your stove budget. Be aware that failure to follow the guidelines could result in a penalty! Once the stove is properly fitted, you will need to make sure you have a notice plate completed. This is another regulation that records all the details of your stove, hearth, chimney and flue.

It should be placed by your hearth, electric meter or water stopcock. If you live in a listed building, it is possible you might need proper planning permission. No — you cannot use stovepipe through the window or roof! The diagram above shows the three most common installation types.

Type 1 would be common in any single story construction. Regular black stove pipe is run upwards from the stove and connects with the Insulated Chimney at a special support box located immediately below the ceiling level.

Insulated chimney is then stacked up until the required height is obtained. All chimneys must extend a minimum of 3 feet above the roof surface and 2 feet higher than any part of the building within 10 feet.

If desired, this chimney could be boxed in with wood framing and stuccoed or sided to match the home. Type 3 is similar to type 1 in that it is a single story installation, but different components are needed due to the slanted ceiling. In this case, the pipe is supported by a bracket at the roof level, and Insulated Chimney Pipe hangs down partially into the room to connect to the interior black stovepipe.

The details as to the building of masonry chimneys are beyond the scope of this document, however there are a few safety and performance issue to keep in mind. The sad truth is that some masons spent so many years building low-temperature chimneys for oil burners, gas burners and fireplaces that the art of proper chimney construction has become almost lost.

These deficiencies can be addressed during new construction by a competent mason, and a properly designed and built masonry chimney is a work of art that can last for generations.

An existing but deficient masonry chimney can often be brought up to spec by installing a UL approved stainless steel liner system. This provides an extra margin of safety as well as improves draft and simplifies cleaning. Not so fast — some thought processes are required here.

Lets start with the fireplace. If they were real smart, they fit some old fiberglass insulation around it so as to stop too much room air from escaping up the chimney made the stove draft stronger too. Chimney professionals soon saw that there were a lot of problems with this setup. The stoves drafted poorly, created lots of creosote and the more-than-occasional chimney fires! As a result of these problems, the Hearth Industry and the National Fire Protection Association put together a set of more modern guidelines.

First, determine if you have a masonry fireplace and chimney. If you have a metal zero clearance fireplace and metal chimney, your options are very limited. Check with your local Hearth Retailer — and confirm in the installation manual or manufacturers literature.

Houses with unused chimneys tend to be older homes, as these structures were often built with multiple chimneys for heating, cooking, etc. Often, these older chimneys are not safe to use without some upgrading. They can be lined with approved stainless steel pipe or restored with special masonry processes ask your chimney sweep. Pay special attention to the wall pass-through, which is the area where your stove pipe will connect to your chimney.

Any wood or combustible material in this are must be cut back to comply with building codes. Special insulated sleeves are available to accomplish this transition.

As previously mentioned, it is not to be used for passing through Walls, Floors or Ceilings.